Mô tả sản phẩm: Advanced Combustion Flue Gas Analyser (up to 4 sensors) EUROTRON UniGas 3000+ Mk3
Description:
The micro-processor hased instrument includes a flue gas analyser, an emissions monitor and an ambient parameters indicator. Two internal electrochemical sensors read the Oxygen (O2) and carbonic monoxide (CO) gas concentration. The gas temperature and air temperature are used in connection with the gas analysis to calculate the efficiency, excess air, and CO2 concentration. A 10 gas parameters programmable table is used for calculations approved in accordance with DIN33962. A third cell (NO or SO2) enables the pollution measurement. The NO concentration can be expressed in terms of NOx as required by ambient laws.
External sensors are available for ambient parameters measurement:s: ambient CO, to check and evaluate gas network leakage and natural gas leakage detector.
UniGas 3000+ Mk3 can install a forth electrochemical sensor to monitor pollution. In this way you can measure simultaneously and using a single unit, NO/NOx and SO2 gas concentration.
- CO dilution to extend the sensor range up to 10%
- Electrovalve for autozero quick start-up
- Draft measurement is possible using the internal pressure sensor and the special gas sample probe.
- The optional internal printer is impact type and the generated document is very legible and has a long time duration.
- The internal standard memory may store up to 250 complete gas analysis divided by Tag.
- More than 10 hours of operations with standard Li-Ion battery pack
- The UniGas has a standard USB serial port and the configuration PC software to configure the analyser.
Specification:
Order accessories below.
- Type: palm-top combustion gas analyser
- Calibration: automatic calibration procedure at instrument switch-On.
- Self-diagnosis: Sensors efficiency test with display diagnostic messages.
- Fuel types: Up to 10 selectable from keyboard (most common preprogrammed).
- Power supply: High capacity Li-ion rechargeable battery pack / external battery charger.
- Charging time: 3h at 90% with instrument off
- Battery life: 10 hours (typical) continuous use (without printing and backlight).
- Printer: Internal impact type 24 columns with paper roll. (10m)
- Printer power supply: from the analyser battery pack.
- Print autonomy: up to 40 reports with full battery (typical).
- Printed report header: 4 programmable lines.
- Display: graphic black LCD with white lamp.
- Flue gas probes: stainless steel shaft with incorporated temperature sensor.
- Memory: up to 250 full analysis data structured by boilers (Tags)
- Serial communication: RS232 interface. USB cable optional.
- Operating temperature: from -5°C to +45°C - from -10 to 90% RH
- Storage temperature: from -20 to +50°C (3 months maximum at temperatures exceeding the operational limits).
- Dimensions and Weight: 115x90x330 mm - 1.1 kg with battery and printer
Included as Standard:
- 2 sensors (O2 + CO 8000ppm H2 compensated with dilution system)
- Li-ION battery + charger module
- Built-in impact printer
- Differential pressure sensor (200 mbars)
- Cell CO dilution system
- Rubber holster magnetic
- PC software GasConfig + DBGas2004 Lite + USB cable (EE700476)
- Instruction manual
- Calibration certificate
- Warranty 1 year
Order code:
UNIGAS 3000+ Mk3- 7825 - A - B - C C - D - E - F - G - H
- Basic Instrument
- 7825 - Unigas 3000+ with sensors (O2 + CO-H2 8000ppm + dilution system)
- A - Sensor N°1
- 1 - O2 (0-25%)
- B - Sensor N°2
- 2H - Sensor N°2 : CO(0-8000ppm) - H2 compensated dilution system
- 2x - CO (0-20000 ppm)
- B - Sensor N°3 & N°4
- 0 - None
- 4 - Sensor N°3 : NO (0-4000 ppm / res. 1ppm) - NOx calculated
- 4LO - Sensor N°3 : NO (0-500 ppm / res. 0,1ppm)
- 5 - Sensor N°4 : NO2 (0-1000 ppm)
- 6 - Sensor N°4 : SO2 (0-4000 ppm)
- D - Sampling Probe (including water trap and line filter)
- 0 - None
- 1D - 180mm sampling dual hose probe BB610051 (Gas or Draft)
- 3 - 300mm sampling dual hose probe BB610046 (Gas or Draft)
- 5D - 750mm sampling dual hose probe BB610046 (Gas or Draft)
- 3 - Options
- 1 - Built-in impact printer
- 3 - Pressure decay program firmware + Gas network leak test kit
- 6 - Electrovalve for autozero quick start-up
- 8 - Internal probe for gas leak detector (sniffer)
- F - Mains adapter / charger
- 1 - 115V ±10% 50/60Hz - USA plug
- 2 - 230V ±10% 50/60Hz - Schuko plug
- 3 - 230V ±10% 50/60Hz - UK plug
- 4 - 230V ±10% 50/60Hz - Europe plug
- 5 - 100V ±10% 50/60Hz - USA/Japan plug
- G - Accessories (up to 5 elective)
- 0 - None
- 1 - DBGas 2004 STANDARD software
- 2 - Magnetic support
- 3V - Vinyl carrying case with shoulder strap
- 3 - ABS rigid carrying case
- 5 - Pt100 remote air temperature sensor (2m cable) and positioning cone
- 7 - Differential pressure connection kit (2 x EE300088)
- 8 - External probe for gas leak detector (sniffer)
- 9 - External CO ambient probe for monitoring
- B - Manual pump for smoke index measurments + 40 filters + table
- H - Calibration certificate
- 1 - Factory certificate (gas, pressure & temperature)
- X - Instruction manual
- ENG - English
Order accessories below.
- BB880028 - ABS carrying case
- BB880043 - Compact rigid carrying case with shoulder strap. Greenline 2000, probes and accessories need 1/3 of the classic carrying case space
- EE880047 - Rubber holster with magnetic support
- BB610051 - 180mm sampling dual hose probe BB610051 (Gas + Draft) max 800°C
- BB610046 - 300mm sampling dual hose probe BB610046 (Gas + Draft) max 800°C
- BB830009 - Ambient CO probe
- BB830010 - Gas sniffer probe
- BB830018 - Pt100 remote air sensor + positioning cone (with 2m cable)
- BB830025 - External probe for natural boiler draft (200 Pa)
- F2132100 - 130mm air K-Type Thermocouple
- F2137100 - 130mm contact K-Type Thermocouple
- F2139000 - Pipe Velcro TC K-type probe
- F2139100 - Tc K-type clamp temperature probe
- F2139200 - Pt100 clamp temperature probe
- BB610057 - 3m extention for dual hose sample probe + Tc
- BB610103 - 6m extention for dual hose sample probe + Tc
- EE300088 - Single hose pressure probe and burner hose kit
- EE300248 - Leak test KIT (pump+hose+adapters)
- F7828000 - Manual pump for smoke index measurments + 40 filters + table
- BB260166 - DBGas 2004 STANDARD software
- BB260224 - DBGas 2004 STANDARD - Upgrade
- EE700476 - USB adaptator cable
