ANS Việt Nam là công ty XNK hàng đầu và là nhà cung cấp chuyên nghiệp các mặt hàng “Máy móc và các thiết bị, dụng cụ đo lường, kiểm tra công nghiệp”
Hãy liên hệ với chúng tôi để có giá tốt nhất.
093 804 7734 |Mr. Lộc|
Email: loc.ans@ansvietnam.com
Công ty chúng tôi là đại lý phân phối của hãng Togami_Chuyên gia cung cấp thiết bị đo và kiểm tra độ dẫn điện, các loại thiết bị đóng cắt (contactor,Relay ...)...balluff Vietnam,Baumer Vietnam,Crouzet Vietnam, Kuebler Vietnam Koganei Vietnam,Celduc Vietnam,Epulse Vietnam,Crydom Vietnam, Raytek Vietnam,Ircon Vietnam ,MTS Vietnam, Kimo Vietnam, Pilz Vietnam, Status Vietnam, newall vietnam,sterilair vietnam, Univer Vietnam, Masibus Vietnam, Elap Vietnam, Setra Vietnam, Suntronix Vietnam, Wise Vietnam, TMTeck Vietnam, dakotainstruments Vietnam, FIC Vietnam, elap encoder vietnam......
Tracing Device & Measuring Instrument | |
| |
|
Uninterruptible Leak Point Tracing Device |
■ | Detection of leak points under uninterrupted power conditions | ■ | Detection of leak points (places) in pressure and earth phases through the signal injection method. | ■ | Easy detection of leak points by simply touching wires or equipment with the receiver. |
| |
|
Wired Route Tracing Device (With an Earth-Leakage Point Locating Function) |
■ | Locating of earth-leakage points (with the power stopped) | ■ | Tracing of breakers and wired routes both in live lines and dead lines | ■ | Circuit voltage indicating function <100V, 200V or 400V is judged by the transmitter atone.> | ■ | Conductivity checking function <Conductivity is checked by inserting the attached cord with a test lead bar into the receiver.> | ■ | Easy judgment by sound and light. |
| |
|
Wired Route Tracing Device |
■ | Checking without cutting power because breakers can be traced in live lines | ■ | Easy assessment by sound and light. |
| |
|
Wired Route Tracing Device (Two-Way Between Power Supply Side And Load Side) |
■ | One person can easily check the load-side (distribution board side)connections from the power supply side (transformer side) both in live lines and dead lines. | ■ | Tracing on the power supply side can also be performed from the load side. | ■ | Easy assessment using sound and light. |
| |
|
Low-Voltage Phase Sequence Indicator |
■ | Simply connect the lead wire clips to a main circuit so that the phase sequences and open phases can be easily checked. | ■ | This lightweight (130g) and compact (28x60X100mm) checker is pocketable. | ■ | Since the connections between the lead wires and main unit are safely constructed so that the live side is a plug-socket type, live parts are not exposed even if the socket is disconnected by chance. | ■ | Lamp indication of measurement results allows reliable judgment. | ■ | The maul unit requiring no batteries for measurement and indication. is economical. At check time, however, circuit voltage needs to be applied. |
| |
|
Harmonic Tracing Device |
■ | This lightweight handy type is convenient for carrying and simple to handle! (Weight: approx. 310g) | ■ | The presence or absence of harmonics can be scanned safely and accurately on high-voltage and lbw-voltage equipment in live lines. | ■ | The second to 40th harmonic current content and total distortion factor are calculated by 512-point fast-Fourier-transform, and are displayed and stored in memory. (Up to 40th harmonic current can be scanned in a few seconds.) | ■ | Fast-Fourier-transform calculation is optimized by setting to 50 or 60Hz commercial frequency with the frequency selector switch. |
| |
| |
High-Voltage Switch & Breaker | |
|
|
|
Switch For Facility Responsibility Border Point With SOG function |
■ | Realization of the small size. | ■ | Resistance food structure that bears the deterioration of the environment. | ■ | Solid structure that is able to confirm easily although it is "be earnest" "the entrance" of switch. | ■ | Control cable that was equipped the standard 10m. |
| |
|
High-Voltage AC Air Load Break Switch |
As the switch for the classification of a/the distribution line optimal. | |
|
High-Voltage AC SF6 Gas Load Break Switch |
It reaches for the classification of the distribution line and the make and break of the capacitor for electric power for as optimal. | |
|
High-Voltage AC Automatic Gas Load Break Switc |
It reaches for the classification of the distribution line and the make and break of the capacitor for electric power for as optimal. | |
|
High-Voltage AC SF6 Gas Circuit Break Switch |
When the accident (the fault) of the electric installation for the house spreads to the distribution line with the cause and become interruption of service electric installations for other houses have a power failure and exert a big influence socially. It is optimal as the section switch and main block device of a factory yard with such influence accident prevention. Protection of the ground fault, overload, short circuit accident. | |
|
High-Voltage AC Fuse Circuit Break Switch |
■ | Even if the fuse fuses it 1 phase it opens three-phase be simultaneous. Therefore there is not the care of an absence phase. | ■ | Fuse replacement is produced safely due to the structure that does not open if the bottom cover does not do the handle to "earnest". Also I do not require a special tool including the hook stick when I replace the fuse. It is possible easily with safe gloves. | ■ | Pulling out it even if the handle is fixed in the input position because it is a handle free ceremony actuation is possible. |
| |
|
High-Voltage AC Automatic Vacuum Load Break Switch |
To the power supply change-over of the important equipment that interruption of service is not permitted. |
Switchboard | |
|
|
|
Corrosion-Proof Type Control Switches |
■ | For the rubber packing between case and cover, the overall- surface packing method is adopted; hence perfect air-tightness is maintained, and even in the case of repeated tension due to push-button operations, no deterioration will occur. | ■ | The case cover is made of premixed resin, which has outstanding corrosion-proofing as compared with ordinary steel or cast-iron plates. Further, since stain-less steel is used for cover-fixing screws and padlock-locking plate, there is no need to worry about corrosion. | ■ | For the OFF push-button, the locking unit using a padlock plate is a standard type; hence by padlocking, it is conformed to Article 107 (2) of the Labor Safety and Hygiene Regulation. |
| |
Bình luận